Mesh belt storage and pre-installation checks help prevent avoidable damage before a new belt enters service. Protect the belt from concentrated loads, unsuitable folding and dragging, then check the machine, seam and installation orientation before carrying out the approved startup procedure.

This guide focuses on the period from warehouse receipt to initial running. It is not a belt-removal procedure or a substitute for the machine manual. Storage position, lifting arrangements, operating tension and startup settings must follow the instructions for the particular belt and equipment.

Store the belt in its specified packaging arrangement

Keep the identification label, packaging information and installation instructions with the belt. These records should remain traceable to the order and specification.

Choose a storage location that limits contamination and exposure to conditions that could damage the material. Keep the belt away from unknown chemicals, heat sources and unnecessary prolonged light exposure, following the supplier's storage requirements.

For a rolled belt, support the core as specified by the packaging design. Avoid uneven loading, unsupported distortion and local compression. Do not assume that hanging or laying a large belt flat is appropriate for every construction.

If the belt will be held as a spare, ask YIHENG about its packaging and storage requirements before changing the supplied arrangement. Record persistent creases, edge distortion or surface damage rather than trying to remove them through unapproved heating or force.

Plan handling before moving or opening the roll

Prepare a clear route and a suitable inspection area. Keep the belt away from the floor, sharp corners and rough surfaces. Select handling equipment and support points according to the package instructions and local safe-working procedures.

Avoid applying an unsuitable pulling force to the seam, belt edge or a small area of fabric. When opening the belt for inspection, support it appropriately and prevent twisting or accidental folds.

Do not leave tools, spare parts or other heavy objects on the belt surface. If abrasion or compression damage is found, mark its location and ask the supplier to assess it before installation.

Complete the machine-side pre-installation checks

Installation must be performed by authorized personnel. Stop the machine, isolate relevant energy sources and verify a safe condition under the site's procedures. Restore required guarding before operation, and never reach toward a moving belt, roller or seam.

Within those safety controls, check:

• Roller and contact surfaces for contamination, burrs, foreign objects or deposits.

• Tensioning, tracking and associated detection devices against the equipment instructions.

• The new belt's dimensions, seam and orientation against the approved documents.

• The installation path for twisting, folding or abnormal edge contact.

• Removal and accounting of tools and temporary restraints before startup.

If the previous belt shows pronounced one-sided wear, record the pattern and investigate the cause. A new belt should not be exposed to an unresolved machine or alignment problem.

Confirm the seam and tension before startup

Set tension using the allowable conditions for the belt and machine, not by feel alone. Increasing tension is not a general remedy for slipping or mistracking. The installation, drive and contact conditions need to be checked first.

Follow the specific seam instructions and confirm the connection, flatness and orientation. Experience with a similar-looking seam does not establish that the same joining method applies to the replacement.

If the documents do not identify the required tension or seam arrangement, resolve the gap with the supplier and machine provider. Do not substitute settings from an unrelated belt model.

Record observations during the approved startup procedure

Once installation and safety checks are complete, follow the machine's prescribed starting speed and adjustment sequence. Observe belt position, abnormal movement, seam passage, edge contact and the behavior of the tracking system.

Stop according to the operating procedure if there is significant rubbing, unusual noise or persistent mistracking. Inspect only after the machine has been made safe. Do not attempt to correct tracking by pulling on a running belt, and do not increase speed while an unexplained fault remains.

Record the installation date, initial tension setting, startup conditions and corrective actions. These observations provide a useful baseline for subsequent dimensional, wear and maintenance comparisons.

Frequently asked questions

Can a mesh belt be folded for storage?

Follow its packaging instructions. Do not change the supplied roll or support arrangement without confirming that the alternative is suitable.

Does intact packaging mean the belt needs no inspection?

No. Check the label, surface, edges and seam after opening, and confirm that the belt matches the order.

Does a crease make a belt unusable?

The answer depends on its severity, location, construction and acceptance requirements. Document it and request an assessment rather than assuming either acceptance or rejection.

Should tension be increased when a new belt mistracks?

Not as an automatic response. Follow the equipment's troubleshooting process and check orientation, tensioning, tracking and contact conditions first.

Can the previous belt's settings be reused?

They can be supplied as reference information. Confirm that they are suitable for the new specification and complete the required startup checks before normal production.

Keep warehouse and installation records together

A continuous record from unpacking to startup helps distinguish shipping condition, handling damage, installation issues and later operating changes.

For a YIHENG belt, send the product reference and machine details when requesting storage, seam or installation information. The nonwoven mesh belt range provides an overview of the available application categories.